![]()
# Inside running coLinux configure eth0 with this static settings: # Slirp for internet connection (outgoing) # Initrd installs modules into the root file system. # Additional kernel parameters (ro = rootfs mount read only) # This parameter will be forward to Linux kernel. # Tell kernel the name of root device (mostly /dev/cobd0, # Swap device, should be an empty file with 128.512MB.Ĭobd1="C:\programs\coLinux\images\swap_file.1gb" #DEBIAN INSTALL DMG WRONG FS TYPE DOWNLOAD## Download and extract preconfigured file from SF "Images for 2.6".Ĭobd0="C:\programs\coLinux\images\3.1gb" Now we can specify root image, swap file and possibly other mount points and also define two ethernet devices - one for pcap bridge and second for TAP adapter: We create a new configuration file (just modify the installed nf):Ĭ:\programs\coLinux> copy nf nf We have to configure the private IP address of the host system (windows):įilesystem images: c:\programs\coLinux\images Now the TAP adapter is installed (but not connected): TAP network adapter is installed (dear Microsoft, sure we want to continue the installation -) We can download (some of) available filesystem images directly during the installation: I choose stable WinPcap 4.0.2 (an alternative could be WinPcap 4.1 beta4). #DEBIAN INSTALL DMG WRONG FS TYPE WINDOWS#ĭevel-coLinux-20081130.exe, see this page for details).ĭuring the installation the WinPcap (The Windows Packet Capture Library) is installed. (an alternative could be the development version 8.0 (kernel 2.6.22.18). In my case it was the stable version 0.7.3 (kernel 2.6.22.18). It can be seen as an alternative to a conventional "dual boot" configuration - but with both systems running at the same time. As a result we get a graphic Linux environment cooperatively running on the Windows hosting system. Also the installation of GNOME desktop environment and NX server is covered. #DEBIAN INSTALL DMG WRONG FS TYPE HOW TO#You can try running FSCK at that point.This post provides a step by step tutorial how to download, install and configure CoLinux with Debian 4.0 file system image. If you run out, you likely have bigger issues and I hope you have good backups. Keep trying until you either run out of superblocks or it works. See if you get the same messabout about bad superblocks. Now try the command to validate the disk again. I've had to go the third or fourth one a couple of times. If not try the next superblock on the list. Your superblocks may be stored elsewhere. You will also want to pick one from the list you get from your partition. Pick an alternate superblock - keep in mind that the first one is the default and its bad so let's not use that one. This will output the alternate superblocks stored on your partition. You don't want to do this if your superblock is OK. Get your error message which says the superblock is bad. Ignoring this step can cause you problems later if it's NOT an EXT4 file system. Your device and your file system (ZFS, UFS, XFS, etc.) may vary so know what you have first. sudo -sįigure out which device - assuming /dev/sdc1 for this example along with EXT4 as its the most common for this explanation. ![]() That concludes my warning on running your system as root. Like many other things, with great power comes great responsibility. If so directed, it will speedily delivery Mr. ![]() Just remember that when you are root, Linux assumes that you know what you're doing when you issue commands. You can sudo yourself silly or just become root for the process. data directory for a data base) so there are times when I don't want to use it or it doesn't work. FSCK can be a "lossy" process because FSCK may want to remove too much data or to remove data from a sensitive location (e.g. I have a different process for this that replaced the bad superblock with one of the alternatives. ![]() Sector size (logical/physical): 512 bytes / 4096 bytes I've already read this mount: wrong fs type, bad option, bad superblock on /dev/sdb on CentOS 6.0 to no avail.įdisk output regarding the drive Disk /dev/sdb: 1000 GiB, 1073741824000 bytes, 2097152000 sectors I've done this stuff many times before and have never ran into anything like this. ![]() I tried mount -t ext4 /dev/sdb1 /mnt/storage2 with identical outcome. In some cases useful info is found in syslog - try Missing codepage or helper program, or other error It resulted in mount: wrong fs type, bad option, bad superblock on /dev/sdb1, Then I tried to mount the drive mkdir /mnt/storage2 I added a new hard drive ( /dev/sdb) to Ubuntu Server 16, ran parted /dev/sdb mklabel gpt and sudo parted /dev/sdb mkpart primary ext4 0G 1074GB. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |